SONIFEX S2-C6SS 6 Way Stereo Source Select Channel with EQ
SONIFEX S2-C6SS 6 Way Stereo Source Select Channel with EQ
The 6 way stereo line source select channel has 6 balanced stereo inputs on a 25 way D-type connector selectable by a 6 way mechanical interlocking switch bank, numbered 1 - 6. A depressed button indicates the selected input. The switch bank also controls 6 sets of remote outputs allowing each source to have a set of start/stop remotes. The remote starts can be set as momentary or latching.
Continuous momentary start can also be enabled such that when the fader is up and the channel is on, each press of the ON button triggers a momentary start. The channel is fitted with EQ as standard and other functions are similar to the S2-CSE Dual Stereo channel with EQ.
The HF and LF controls are used to adjust the equalisation of the signal. The HF control boosts and cuts the signal by 10dB at 6.5kHz. The LF control boosts and cuts the signal by 10dB at 100Hz. The EQ button places the equalisation in and out of the signal path and is illuminated yellow when the EQ is active. The channel can be used to control either one of two separate timer displays.
SPECIFICATIONS
Input/Output Impedances |
|
Mic Input: | > 1k5Ω electronically balanced |
Mono Line Input: | > 20kΩ electronically balanced |
Stereo Line Input: | > 20kΩ electronically balanced |
PGM & AUD Output: | < 75Ω electronically balanced |
Mono Output: | < 75Ω electronically balanced |
Monitor Outputs: | < 75Ω unbalanced |
AES Input/Output: | 110Ω |
S/PDIF Input/Output: | 75Ω |
BNC Wordclock input: | 50Ω |
Input/Output Gain Range |
|
Mic Input: | Preset pot +13dB to +66dB ref -50dBu, TRIM pot ±12dB |
Mono Line Input: | Preset pot -6dB to +10dB ref 0dBu, TRIM pot ±12dB |
Stereo Line Input: | Preset pot -6dB to +10dB ref 0dBu, TRIM pot ±12dB |
Telco Input: | Preset pot -6dB to +10dB ref 0dBu, TRIM pot ±12dB |
Telco Output: | Preset pot -6dB to +4dB ref 0dBu |
Mix Minus Input: | Preset pot -6dB to +10dB ref 0dBu, TRIM pot ±12dB |
Mix Minus Output: | Preset pot -3dB to +3dB ref 0dBu |
Digital Input: | 0dBFS = +12dBu on input; TRIM pot ±12dB allowing 0dBu to +24dBu |
Digital Output: | 0dBFS = +18dBu |
Frequency Response |
|
Mic Input: | 40Hz to 20kHz, -1dB,+0dB (-3dB at 130Hz with HPF in) |
Line Inputs: | 20Hz to 20kHz, - 0.5dB,+0dB |
RIAA Input: | 30Hz to 16kHz ±1.5dB RIAA equalised |
Noise (20Hz to 20kHz) |
|
Mic Input E.I.N.: | -129dB with 150Ω source |
Stereo Inputs (fader down, no routing): | -89dB ref 0dB |
Stereo Inputs (fader down, one channel routed): | -89dB |
Stereo Inputs (unity gain, no routing): | -89dB |
Stereo Inputs (unity gain, one channel routed): | -86dB |
Stereo Inputs (unity gain, two channels routed): | -83dB |
Distortion | |
Total Harmonic Distortion: | 0.015% at 1kHz, 0dB 0.025% at 10kHz, 0dB |
Crosstalk |
|
Inter-channel: | < -90dBu |
Stereo: | -90dBu at 1kHz |
Equalisation |
|
LF Shelving at 100Hz: | ±7dB |
HF Shelving at 6.5kHz: | ±7dB |
Range |
|
Pan Range: | off/-3dB centre/off |
Balance Range: | ±6dB |
Common Mode Rejection Ratio |
|
Mic Input: | > 100dB at 70dB gain |
Digital I/O |
|
Sync Input Sample Rate: | 30kHz - 100kHz |
Output Sample Rates (Using Onboard Clock): | 32kHz, 44.1kHz, 48kHz, & 96kHz |
Output Sample Width: | 16, 20, 24 bit (24 bit on V2 ODA/ODP) |
Output |
|
Headphone Output Load: | >45Ω, 400Ω recommended |
Maximum Output (Analogue): | +26dBu balanced into 2kΩ or greater |
Power |
|
Power (S2-PSU): | Filtered IEC, switchable 115V, 230V, fused, 210W max. |
Dimensions (S2-PSU): (Raw): |
48cm (W) x 24.3cm (D) x 8.8cm (H) 19” (W) x 10” (D) x 3.5” (H) |
Dimensions (S2-PSU): (Boxed): |
51cm (W) x 41.5cm (D) x 17cm (H) 20” (W) x 16.3” (D) x 6.7” (H) |
Weight (S2-PSU): | Nett: 6kg Gross: 7.8kg Nett: 13.2lbs Gross: 17lbs |
Dimensions (S2-PSUS): (Raw): |
48cm (W) x 23cm (D) x 4.4cm (H) 19” (W) x 9” (D) x 1.7” (H) |
Dimensions (S2-PSUS): (Boxed): |
55cm (W) x 39.3cm (D) x 8.5cm (H) 21.6” (W) x 15.5” (D) x 3.4” (H) |
Weight (S2-PSUS): | Nett: 1.58kg Gross: 2kg Nett: 3.5lbs Gross: 4.4lbs |